Description
A 4-media remineralization filter in the standard 10″ × 2″ inline size with built-in 3/8″ quick-connect ports. Installed as the last stage after an RO membrane, it adds minerals back and gently raises pH, for smoother-tasting drinking water on 3/8″ water lines.
What this remineralization filter does
Reverse osmosis removes most dissolved minerals, so RO water can taste flat. MIN-MCB-QC38 holds four mineral media — natural mineral stone, coral red stone, maifan stone and bio-ceramic media. As RO water passes through, they slowly release calcium, magnesium and other trace minerals back into the water and gently raise pH to about 7.5–8.3. Actual pH depends on your water, flow and the age of the filter.
Mineral, not high-alkaline. This filter is for people who want RO water to taste more like good spring water, not strongly alkaline water. For a higher pH (about 8.2–9.5), choose our 3/8″ alkaline inline filter (ALC-FMB-QC38).
Install it last: after the RO membrane and after the carbon post-filter. The ports are built into the filter body — push 3/8″ OD tubing straight in, with no fittings to screw on and no thread tape. A TDS meter will read a little higher after this filter than right after the membrane, because it adds minerals back. That is normal.
Key benefits
- ✓ Adds calcium, magnesium and trace minerals back to RO water
- ✓ Gently raises pH, about 7.5–8.3 — not high-alkaline
- ✓ Four natural mineral media for a smoother taste
- ✓ Built-in 3/8″ quick-connect ports: push in, no tools or tape
- ✓ Standard 10″ × 2″ inline size, last stage for under-sink RO
- ✓ Same-size replacement for Omnipure K2548-KK, SpiroPure SP-IM382QC and more*
Specifications
What it does — and doesn’t
A remineralization filter conditions RO water. It isn’t a treatment stage.
Gently raises pH
Smoother taste
Chlorine (use carbon first)
Sediment
Bacteria
Mineral or alkaline: which one?
See the 3/8″ alkaline filter →
Where to use it
- Under-sink RO systems with 3/8″ tubing to the faucet — as the last stage
- Tankless RO and drinking-water lines on 3/8″ tubing
- Replacing a worn-out 10″ × 2″ inline mineral or calcite filter
- 1/4″ tubing — choose the 4-in-1 remineralization filter (1/4″ & 3/8″) or use 3/8″ × 1/4″ adapters
- Before the RO membrane or before a carbon filter — it goes last
- Hot water
- DI or lab water, where you want 0 ppm
Compatible systems & replacement filters
MIN-MCB-QC38 is a standard 10″ × 2″ inline filter with built-in 3/8″ quick-connect ports. It can replace the same-size 3/8″ mineral, calcite and alkaline post-filters below.*
Also searched as: K2548KK · K2551KK · SPIM382QC · FA15US · 3/8 remineralization filter · inline mineral filter 3/8 quick connect · RO remineralization filter · mineral filter for reverse osmosis
Check before you order. Your old filter should be about 2″ across and 10″ long, on 3/8″ OD tubing. Filters 2.5″ across use bigger mounting clips. Not sure? Send us a photo and we’ll confirm the fit.
Replacing an alkaline filter? It fits the same way, but your pH will be lower (about 7.5–8.3 instead of 9+). If you liked the higher pH, choose the alkaline version.
Fit questions
My RO system has 1/4″ tubing. Will it work?
Not directly — the ports take 3/8″ tubing. Choose the 4-in-1 remineralization filter, which comes with 1/4″ and 3/8″ fittings, or add two 3/8″ × 1/4″ reducing adapters.
Where exactly does it go?
After the RO membrane and after the carbon post-filter, right before the faucet. Point the flow arrow on the label toward the faucet.
Why does my TDS meter read higher after it?
Because it adds minerals back. A small rise after this stage is normal and expected.
How do I know when to replace it?
Every 6–12 months or about 400 gallons, or sooner when the taste goes flat again.
Good to know before you install
- Pull out the port plugs before you connect the tubing.
- Flow arrow toward the faucet. It’s on the label.
- Cut the tubing square (90°), push it in until it stops, then tug gently to check. To release, press the collet and pull.
- Flush 5 minutes or more before drinking. The first water may look slightly cloudy from mineral dust — that clears.
- Check for leaks after 10 minutes and again the next day.
* Omnipure, SpiroPure and iSpring, and their model names, are trademarks of their respective owners. My Water Club is not affiliated with, sponsored by or endorsed by these companies, and this filter is not made by them. Brand and model names are used only to identify the same-size filters it can replace. Please check your system before ordering.










Reviews
There are no reviews yet.