My Water Club Product Support

Granular Activated Carbon (GAC) Filter — 10″ × 4.5″

GAC-10BB

Specifications, how to change it, which housings it fits, and what to pair it with.

My Water Club GAC-10BB GAC carbon cartridge
Is this your filter?

Check the cartridge in your housing against this list.

  • ✓A large cartridge, about 4.5″ wide and 10″ long
  • ✓Heavier than a sediment cartridge — filled with carbon granules
  • ✓Label reads GAC-10BB · 25 micron
  • ✓Sits after the sediment stage
Measure your housing before you order
  • About 4.5″ wide and 10″ tall, with 1″ ports: this cartridge fits.
  • Narrow, about 2.5″ wide with 3/4″ ports: you need a 10″ × 2.5″ cartridge. Find your model →
  • About 4.5″ wide and 20″ tall: you need a 20″ × 4.5″ cartridge. Ask us →

Specifications

Model / SKU GAC-10BB
Media Granular activated carbon (GAC)
Rating 25 micron (nominal)
Size Standard 10″ × 4.5″ heavy-duty whole-house housings
Position Stage 2 — carbon, after sediment
Pressure Max 90 PSI · above 80 PSI, fit a pressure regulator
Temperature 40–100 °F (4–38 °C), cold water only
Typical life 3–12 months
Brand My Water Club

Reorder this filter

Order the same cartridge

Order by SKU GAC-10BB.

View on MyWaterClub.com →

Buy on Amazon →
Upgrade option
CGAC-10BB — Coconut shell GAC

Coconut carbon for taste & VOCs at full GAC flow. Same size and same position.

Support page →  ·  View on MyWaterClub.com →

My Water Club systems that use this filter

System Where it goes More
Triple-stage system (WHS-3SGC-10BB-E) second housing System support page →
Triple-stage system with coconut carbon block (WHS-3SGCACB-10BB-A) second housing View system →

It also fits other standard 10″ × 4.5″ housings, including our HOUSING10BB.

Good to know

  • Chlorine taste returning is your signal to change it — earlier than the calendar if needed.
  • City uses chloramine? Standard carbon struggles with it. Use CAT-10BB catalytic carbon instead.
  • Coconut option: CGAC-10BB coconut-shell GAC fits the same position.

When to change your filter

Part Typical interval Change sooner if…
This cartridge (GAC-10BB) 3–12 months Chlorine taste or smell comes back · heavy household water use
Housing O-ring Inspect at every change · replace every 12–24 months Cracked, flattened, brittle or weeping at the seam (O-ring sets)
Filter housing About every 3–4 years Crazing, hairline cracks, cloudiness, or a leak a new O-ring doesn’t stop (HOUSING10BB)

Intervals are estimates. Water chemistry, pressure and usage all change them.

Changing your filter

  1. Shut off the water: close the valves on both sides of the system (or the bypass), or the main shut-off.
  2. Open a cold tap downstream, then press the pressure release button on the cap until the hissing stops.
  3. Put a bucket and towels underneath — a 10″ × 4.5″ housing holds over a gallon of water.
  4. Unscrew the sump with the housing wrench (counterclockwise, looking up from below), supporting its weight.
  5. Remove the old cartridge and rinse the sump with clean water only — no soap or bleach.
  6. Inspect the O-ring and replace it if it’s damaged. Coat it lightly with food-grade silicone grease (never petroleum jelly).
  7. Unwrap the new cartridge and stand it centered on the post in the sump.
  8. Screw the sump on by hand, then snug it with the wrench — no more than a quarter turn. Don’t overtighten.
  9. Turn the water back on slowly. Press the release button to let air out, and check for leaks now and again after 12 hours.
  10. Run a cold tap for 5 minutes. New carbon releases fine black dust at first — that’s normal and clears quickly.
  11. Write the change date on the housing, a magnet or the manual.

What to put before and after it

Keep a sediment stage in front of it, so grit doesn’t clog the carbon. A carbon block after it polishes taste and odor, and a scale inhibitor can go last.

Position Cartridge Good for What it does
Before it SED5-10BB Stage 1 on most water 5 µm melt-blown polypropylene · captures dirt, silt, sand & rust particles
Before it SED5-PLT-10BB Heavy sediment, well water 5 µm pleated polyester · rinse and reuse
After it CTO-10BB Everyday city water Carbon block, 10 µm · reduces chlorine, taste & odor · lowest cost block
After it CACB-10BB Taste & odor Coconut carbon block, 10 µm · the usual pick for taste & odor · 6–12 month life
After it SCALE-10BB Limescale Polyphosphate helps prevent scale in pipes & appliances · not a softener

Browse all 10″ × 4.5″ cartridges → · Free basic water testing in San Diego →

Common questions

  1. The chlorine taste is back.
    The carbon is used up. Change the cartridge, even if it’s earlier than the calendar says.
  2. My city uses chloramine. Will this work?
    Standard carbon has limited effect on chloramine. Use CAT-10BB catalytic carbon in this position instead.
  3. Water pressure has dropped through the house.
    Check the sediment stage first — it’s usually the one that clogs. If sediment is fresh and pressure is still low, change this cartridge.
  4. There are black specks or gray water right after a change.
    Normal carbon fines from a new cartridge. Run a cold tap for 5 minutes. If specks keep coming for days, check that the cartridge is seated on the post.
  5. There’s a leak where the housing meets the cap.
    The O-ring isn’t seated, or it’s worn. Shut off the water, press the release button, then reseat or replace the O-ring and coat it lightly with food-grade silicone grease.
  6. The housing won’t unscrew.
    Usually there’s still pressure inside, or it was overtightened. Make sure the water is off, press the release button, then use the housing wrench.

Need help?

Contact us
Send a photo of your cartridge or housing and we’ll identify it.

Get in touch →

All manuals
Instructions for every My Water Club system.

Browse manuals →

San Diego area service
In-person help and free basic water testing.

Local service →

Warranty & returns
What’s covered and how to start a return.

View policy →

Call or text (858) 345-7345. Bought on Amazon? You can also use Your Orders › Contact seller.

Scope and disclaimers

This cartridge treats the contaminants named on this page only. It doesn’t make unsafe water safe to drink. Treat untested well water, or water under a boil-water advisory, before relying on any filter.

Filter life and reduction performance depend on your water chemistry, pressure and usage, so results vary from home to home. Intervals on this page are typical estimates, not guarantees. Our filters are not certified to treat water of unknown quality and are not a substitute for testing your water. Descriptions use general, qualified language and are not health claims.