Granular Activated Carbon (GAC) Filter — 10″ × 4.5″
Specifications, how to change it, which housings it fits, and what to pair it with.

Check the cartridge in your housing against this list.
- ✓A large cartridge, about 4.5″ wide and 10″ long
- ✓Heavier than a sediment cartridge — filled with carbon granules
- ✓Label reads GAC-10BB · 25 micron
- ✓Sits after the sediment stage
- About 4.5″ wide and 10″ tall, with 1″ ports: this cartridge fits.
- Narrow, about 2.5″ wide with 3/4″ ports: you need a 10″ × 2.5″ cartridge. Find your model →
- About 4.5″ wide and 20″ tall: you need a 20″ × 4.5″ cartridge. Ask us →
Specifications
| Model / SKU | GAC-10BB |
| Media | Granular activated carbon (GAC) |
| Rating | 25 micron (nominal) |
| Size | Standard 10″ × 4.5″ heavy-duty whole-house housings |
| Position | Stage 2 — carbon, after sediment |
| Pressure | Max 90 PSI · above 80 PSI, fit a pressure regulator |
| Temperature | 40–100 °F (4–38 °C), cold water only |
| Typical life | 3–12 months |
| Brand | My Water Club |
Reorder this filter
Coconut carbon for taste & VOCs at full GAC flow. Same size and same position.
My Water Club systems that use this filter
| System | Where it goes | More |
|---|---|---|
| Triple-stage system (WHS-3SGC-10BB-E) | second housing | System support page → |
| Triple-stage system with coconut carbon block (WHS-3SGCACB-10BB-A) | second housing | View system → |
It also fits other standard 10″ × 4.5″ housings, including our HOUSING10BB.
Good to know
When to change your filter
| Part | Typical interval | Change sooner if… |
|---|---|---|
| This cartridge (GAC-10BB) | 3–12 months | Chlorine taste or smell comes back · heavy household water use |
| Housing O-ring | Inspect at every change · replace every 12–24 months | Cracked, flattened, brittle or weeping at the seam (O-ring sets) |
| Filter housing | About every 3–4 years | Crazing, hairline cracks, cloudiness, or a leak a new O-ring doesn’t stop (HOUSING10BB) |
Intervals are estimates. Water chemistry, pressure and usage all change them.
Changing your filter
- Shut off the water: close the valves on both sides of the system (or the bypass), or the main shut-off.
- Open a cold tap downstream, then press the pressure release button on the cap until the hissing stops.
- Put a bucket and towels underneath — a 10″ × 4.5″ housing holds over a gallon of water.
- Unscrew the sump with the housing wrench (counterclockwise, looking up from below), supporting its weight.
- Remove the old cartridge and rinse the sump with clean water only — no soap or bleach.
- Inspect the O-ring and replace it if it’s damaged. Coat it lightly with food-grade silicone grease (never petroleum jelly).
- Unwrap the new cartridge and stand it centered on the post in the sump.
- Screw the sump on by hand, then snug it with the wrench — no more than a quarter turn. Don’t overtighten.
- Turn the water back on slowly. Press the release button to let air out, and check for leaks now and again after 12 hours.
- Run a cold tap for 5 minutes. New carbon releases fine black dust at first — that’s normal and clears quickly.
- Write the change date on the housing, a magnet or the manual.
What to put before and after it
Keep a sediment stage in front of it, so grit doesn’t clog the carbon. A carbon block after it polishes taste and odor, and a scale inhibitor can go last.
| Position | Cartridge | Good for | What it does |
|---|---|---|---|
| Before it | SED5-10BB | Stage 1 on most water | 5 µm melt-blown polypropylene · captures dirt, silt, sand & rust particles |
| Before it | SED5-PLT-10BB | Heavy sediment, well water | 5 µm pleated polyester · rinse and reuse |
| After it | CTO-10BB | Everyday city water | Carbon block, 10 µm · reduces chlorine, taste & odor · lowest cost block |
| After it | CACB-10BB | Taste & odor | Coconut carbon block, 10 µm · the usual pick for taste & odor · 6–12 month life |
| After it | SCALE-10BB | Limescale | Polyphosphate helps prevent scale in pipes & appliances · not a softener |
Browse all 10″ × 4.5″ cartridges → · Free basic water testing in San Diego →
Common questions
- The chlorine taste is back.
The carbon is used up. Change the cartridge, even if it’s earlier than the calendar says. - My city uses chloramine. Will this work?
Standard carbon has limited effect on chloramine. Use CAT-10BB catalytic carbon in this position instead. - Water pressure has dropped through the house.
Check the sediment stage first — it’s usually the one that clogs. If sediment is fresh and pressure is still low, change this cartridge. - There are black specks or gray water right after a change.
Normal carbon fines from a new cartridge. Run a cold tap for 5 minutes. If specks keep coming for days, check that the cartridge is seated on the post. - There’s a leak where the housing meets the cap.
The O-ring isn’t seated, or it’s worn. Shut off the water, press the release button, then reseat or replace the O-ring and coat it lightly with food-grade silicone grease. - The housing won’t unscrew.
Usually there’s still pressure inside, or it was overtightened. Make sure the water is off, press the release button, then use the housing wrench.
Need help?
Call or text (858) 345-7345. Bought on Amazon? You can also use Your Orders › Contact seller.
Scope and disclaimers
This cartridge treats the contaminants named on this page only. It doesn’t make unsafe water safe to drink. Treat untested well water, or water under a boil-water advisory, before relying on any filter.
Filter life and reduction performance depend on your water chemistry, pressure and usage, so results vary from home to home. Intervals on this page are typical estimates, not guarantees. Our filters are not certified to treat water of unknown quality and are not a substitute for testing your water. Descriptions use general, qualified language and are not health claims.