Description
A compressed coconut shell carbon block in the standard 10″ × 2″ inline size, rated 5 micron, with built-in 1/4″ quick-connect ports: it reduces chlorine taste and odor on RO systems, fridge, ice maker and coffee lines.
What this inline carbon block filter does
CB5-QC14 is an inline filter packed with compressed coconut shell activated carbon, formed into a solid block. Water passes through the block, where the carbon reduces chlorine taste and odor. The 5 micron block also traps fine particles, which is why it works best after a sediment pre-filter, so it doesn’t clog early.
The ports are built into the filter body: push 1/4″ OD tubing straight in. No fittings to screw on and no thread tape.
A carbon block is a different design from the loose granular carbon (GAC) in most inline filters: the carbon is finer and tightly packed, so water passes through more carbon surface. GAC filters usually flow a little faster. Neither type reduces dissolved solids (TDS), fluoride or hardness — that’s a job for an RO membrane.
Key benefits
- ✓ Coconut shell carbon block: reduces chlorine taste and odor
- ✓ 5 micron block also traps fine particles
- ✓ Built-in 1/4″ quick-connect ports: push in, no tools or tape
- ✓ Standard 10″ × 2″ inline size
- ✓ Lasts 6–12 months or about 1,500 gallons
- ✓ Same-size replacement for Omnipure K2533-JJ, Hydronix ICF-10Q, Aquatic Life RO Buddie carbon and more*
Specifications
Helps reduce
What this filter targets — and what it isn’t built for.
Chlorine odor
Fine particles
Dissolved solids (TDS)
Fluoride
Hardness
Bacteria
Where to use it
- Countertop RO with 1/4″ tubing — carbon stage before or after the membrane
- Under-sink RO — in place of the 10″ × 2″ inline post-carbon filter
- Refrigerator, ice maker and coffee maker lines
- Water coolers and other cold-water lines with 1/4″ tubing
- Without a sediment pre-filter on dirty or well water — it will clog early
- 3/8″ tubing — choose the 3/8″ version
- Before a mineral or alkaline filter — carbon goes first, minerals last
- Hot water, or pressure above 90 PSI
Which inline filter goes where?
MyWaterClub 1/4″ quick-connect inline filters, in the order water flows through them.
Compatible systems & replacement filters
CB5-QC14 is a standard 10″ × 2″ inline carbon filter with built-in 1/4″ quick-connect ports. It fits the systems below and can replace the same-size carbon filters listed after them.*
Systems it fits
Replacement for Omnipure K2533-JJ, Hydronix ICF-10Q, Aquatic Life 330250 & more
Also searched as: K2533JJ · K2540JJ · T33 post filter · ICF10Q · SPIC100QC · CT24CAB · RO Buddie carbon filter · 10 x 2 inline carbon block
Check before you order. Your old filter should be about 2″ across and 10″ long, on 1/4″ OD tubing. Filters 2.5″ across (for example Omnipure K5522 or K5621) use bigger mounting clips. Not sure? Send us a photo and we’ll confirm the fit.
Old filter has threaded ends? Pull the tubing out of its screw-in fittings, cut the ends square and push them into CB5-QC14’s ports. The old fittings aren’t needed.
Fit questions
Does CB5-QC14 fit the Aquatic Life RO Buddie?
Yes, as Stage 2. Both are 10″ × 2″ carbon blocks. The RO Buddie cartridge has threaded ends with quick-connect fittings screwed in; CB5-QC14 has the ports built in, so you push the 1/4″ tubing straight in. Pair it with our SED-QC for Stage 1.
Can I use it as the post-carbon (T33) filter on my under-sink RO?
Yes, if your post-filter is a 10″ × 2″ inline on 1/4″ tubing with quick-connect fittings. Match the flow arrow to the direction toward the faucet.
Is a carbon block better than GAC?
It’s different. The compressed block uses finer, tightly packed carbon and also traps fine particles, but it usually flows a little slower and needs a sediment filter in front of it. GAC flows freely and is the classic RO post filter.
Can I use it on my fridge line?
Yes, on 1/4″ tubing. On well water or water with sediment, put SED-QC in front of it.
Good to know before you install
- Flow arrow toward the faucet or appliance. It’s on the label.
- Cut the tubing square (90°), push it in until it stops, then tug gently to check. To release, press the collet and pull.
- Flush the new filter for at least 5 minutes. A little carbon dust at first is normal.
- Testing TDS? Wait about a week: fresh carbon releases a little dust that can add a few ppm at first.
- Change it every 6–12 months or about 1,500 gallons, sooner if flow drops or the chlorine taste returns.
- Install guide: mywaterclub.com/m/inline
† Pentek® is a registered trademark of Pentair. * APEC, Aquatic Life and RO Buddie, Hydronix, Omnipure and SpiroPure, and their model names, are trademarks of their respective owners. My Water Club is not affiliated with, sponsored by or endorsed by these companies, and this filter is not made by them. Brand and model names are used only to identify systems this filter fits and the same-size filters it can replace. Please check your system before ordering.










Reviews
There are no reviews yet.