Description
A 5 micron inline sediment filter in the standard 10″ × 2″ size with built-in 1/4″ quick-connect ports: the first stage that catches sand, silt, rust and dirt before they reach your carbon filters, RO membrane or appliance.
What this inline sediment filter does
SED-QC is a melt-blown polypropylene sediment filter rated 5 micron. Placed first in a 1/4″ water line, it traps sand, silt, rust flakes and dirt, so the filters and equipment after it don’t clog with grit.
The ports are built into the filter body: push 1/4″ OD tubing straight in. There are no fittings to screw on and no thread tape. A flow arrow is molded into the body, so it can’t wear off.
It is a sediment-only stage. It doesn’t reduce chlorine, taste, odor or dissolved solids (TDS). Pair it with a carbon filter or an RO system for those.
Key benefits
- ✓ 5 micron nominal: catches sand, silt, rust and dirt particles
- ✓ Built-in 1/4″ quick-connect ports: push in, no tools or tape
- ✓ Standard 10″ × 2″ inline size
- ✓ Protects carbon filters, RO membranes and appliances from grit
- ✓ Molded flow arrow and port plugs to keep it clean until install
- ✓ Same-size replacement for APEC CT-1SED, Omnipure K2505-JJ and more*
Specifications
Helps reduce
What this filter targets — and what it isn’t built for.
Rust particles
Dirt & debris
Chlorine / taste
Dissolved solids (TDS)
Chemicals
Bacteria
Where to use it
- Countertop RO systems with 1/4″ tubing — Stage 1
- Refrigerator and ice maker lines (before the fridge’s own filter)
- Coffee makers, espresso machines and water coolers
- In front of an inline carbon, DI or mineral filter
- Under-sink RO systems — they already have a large sediment stage
- 3/8″ tubing (needs a 3/8″ filter or reducers)
- Hot water, or pressure above 90 PSI
Which inline filter goes where?
The MyWaterClub 1/4″ quick-connect inline range, in the order water flows through them.
Compatible systems & replacement filters
SED-QC is a standard 10″ × 2″ inline sediment filter, rated 5 micron, with built-in 1/4″ quick-connect ports. It fits the systems below as Stage 1 and can replace the same-size sediment filters listed after them.*
Systems it fits (Stage 1)
Replacement for Omnipure K2505-JJ, APEC CT-1SED, Hydronix ISF-10Q & more
Also searched as: K2505JJ · K2505 · CT1SED · ISF10Q · SPIS105QC · RO Buddie sediment filter · 10 x 2 inline sediment filter
Check before you order. Your old filter should be about 2″ across and 10″ long, on 1/4″ OD tubing. Filters 2.5″ across use bigger mounting clips. Not sure? Send us a photo and we’ll confirm the fit.
Old filter has threaded ends? Some inline filters (Hydronix ISF-10, SpiroPure SP-IS105, Aquatic Life RO Buddie) have 1/4″ female threads with screw-in fittings. SED-QC doesn’t need those fittings: pull the tubing out of the old fittings, cut the ends square and push them into SED-QC’s ports.
Fit questions
Does SED-QC fit the Aquatic Life RO Buddie?
Yes, as Stage 1. It has the same 10″ × 2″ size and 5 micron rating as the RO Buddie sediment cartridge. The RO Buddie cartridge has threaded ends with quick-connect fittings screwed in; SED-QC has the quick-connect ports built in, so you push the 1/4″ tubing straight in and keep the old fittings as spares.
Can I use it instead of the APEC CT-1SED?
Yes. Both are 10″ inline sediment pre-filters with 1/4″ quick-connect ports for Stage 1 of APEC’s RO-CTOP family.
Is it the same as Omnipure K2505-JJ?
Same type: 5 micron polypropylene sediment, 10″ × 2″, 1/4″ quick-connect ports. Omnipure’s pressure rating is higher (125 PSI vs our 90 PSI), so check your line pressure.
Do I need it on my under-sink RO?
No. Under-sink RO systems already start with a 10″ × 2.5″ sediment cartridge. Use SED-QC on countertop RO, fridge, ice maker and coffee lines.
Good to know before you install
- Flow arrow toward the faucet or appliance. It’s molded into the body.
- Cut the tubing square (90°) and push it in until it stops, then tug gently to check. A slanted cut is the usual cause of a leak.
- Flush the new filter for at least 5 minutes before using the water.
- Change it every 3–12 months, sooner if flow slows down. On water with lots of sediment it can clog quickly.
- Step-by-step guide with photos: mywaterclub.com/sed5-qc (also on the QR code on the label).
* APEC, Aquatic Life and RO Buddie, Hydronix, Omnipure, SpiroPure and TGI Pure, and their model names, are trademarks of their respective owners. My Water Club is not affiliated with, sponsored by or endorsed by these companies, and this filter is not made by them. Brand and model names are used only to identify systems this filter fits and the same-size filters it can replace. Please check your system before ordering.













Reviews
There are no reviews yet.