Description
A compressed coconut shell carbon block in the standard 10″ × 2″ inline size, rated 5 micron, with built-in 3/8″ quick-connect ports: it reduces chlorine taste and odor on 3/8″ water lines — under-sink RO post-filters, water coolers, coffee machines and appliance lines.
What this inline carbon block filter does
CB5-QC38 is an inline filter packed with compressed coconut shell activated carbon, formed into a solid block. Water passes through the block, where the carbon reduces chlorine taste and odor. The 5 micron block also traps fine particles, which is why it works best after a sediment pre-filter, so it doesn’t clog early.
The ports are built into the filter body: push 3/8″ OD tubing straight in. No fittings to screw on and no thread tape.
A carbon block is a different design from the loose granular carbon (GAC) in most inline filters: the carbon is finer and tightly packed, so water passes through more carbon surface. GAC filters usually flow a little faster. Neither type reduces dissolved solids (TDS), fluoride or hardness — that’s a job for an RO membrane.
Key benefits
- ✓ Coconut shell carbon block: reduces chlorine taste and odor
- ✓ 5 micron block also traps fine particles
- ✓ Built-in 3/8″ quick-connect ports: push in, no tools or tape
- ✓ Standard 10″ × 2″ inline size
- ✓ Lasts 6–12 months or about 1,500 gallons
- ✓ Same-size replacement for Omnipure K2533-KK, Hydronix ICF-10Q38, SpiroPure SP-IC380QC and more*
Specifications
Helps reduce
What this filter targets — and what it isn’t built for.
Chlorine odor
Fine particles
Dissolved solids (TDS)
Fluoride
Hardness
Bacteria
Where to use it
- Under-sink RO — in place of a 10″ × 2″ post-carbon filter on 3/8″ tubing
- Water coolers, coffee and espresso machines with 3/8″ lines
- Refrigerator, ice maker and other cold-water appliance lines with 3/8″ tubing
- Works on its own; lasts longer after a sediment pre-filter
- Without a sediment pre-filter on dirty or well water — it will clog early
- 1/4″ tubing — choose the 1/4″ version (CB5-QC14)
- Before a mineral or alkaline filter — carbon goes first, minerals last
- Hot water, or pressure above 90 PSI
Pick your tubing size
Same coconut carbon block inside — only the ports differ. Not sure which tubing you have? Measure its outside diameter: 1/4″ is about the width of a pencil, 3/8″ is noticeably thicker.
Compatible systems & replacement filters
CB5-QC38 is a standard 10″ × 2″ inline carbon filter with built-in 3/8″ quick-connect ports. It can replace the same-size 3/8″ carbon filters below.*
Also searched as: K2533KK · K2540KK · IL10GACX38QC · 5TCR38 · ICF10Q38 · SPIC380QC · 3/8 inline carbon filter · 10 x 2 inline carbon block 3/8
Check before you order. Your old filter should be about 2″ across and 10″ long, on 3/8″ OD tubing. Filters 2.5″ across use bigger mounting clips. Not sure? Send us a photo and we’ll confirm the fit.
Most of these are GAC. CB5-QC38 is a compressed carbon block: it uses finer, tightly packed carbon and also traps fine particles, but usually flows a little slower than loose GAC.
Fit questions
Can I use it as the post-carbon filter on my under-sink RO?
Yes, if your post-filter is a 10″ × 2″ inline on 3/8″ tubing with quick-connect fittings, like the Omnipure K2533-KK. Match the flow arrow toward the faucet. If your tubing is 1/4″, use CB5-QC14.
Does it need a sediment pre-filter?
It works on its own, but a sediment filter in front keeps the block from clogging early, especially on well water. On a 3/8″ line you can use our 5 micron sediment filter with 3/8″ adapters.
Is it the same filter as CB5-QC14?
Same coconut carbon block, same size and ratings. Only the ports differ: 3/8″ here, 1/4″ on CB5-QC14.
Good to know before you install
- Flow arrow toward the faucet or appliance. It’s on the label.
- Cut the tubing square (90°), push it in until it stops, then tug gently to check. To release, press the collet and pull.
- Flush the new filter for at least 5 minutes. A little carbon dust at first is normal.
- Testing TDS? Wait about a week: fresh carbon releases a little dust that can add a few ppm at first.
- Change it every 6–12 months or about 1,500 gallons, sooner if flow drops or the chlorine taste returns.
- Install guide: mywaterclub.com/m/inline
* APEC, EcoWater, Hydronix, Omnipure and SpiroPure, and their model names, are trademarks of their respective owners. My Water Club is not affiliated with, sponsored by or endorsed by these companies, and this filter is not made by them. Brand and model names are used only to identify the same-size filters it can replace. Please check your system before ordering.










Reviews
There are no reviews yet.