My Water Club Product Support

Salt-Free Scale Inhibitor Filter — 10″ × 4.5″

SCALE-10BB

Specifications, how to change it, which housings it fits, and what to pair it with.

My Water Club SCALE-10BB scale inhibitor cartridge
Is this your filter?

Check the cartridge in your housing against this list.

  • ✓A large cartridge, about 4.5″ wide and 10″ long
  • ✓Filled with white polyphosphate crystals
  • ✓Label reads SCALE-10BB
  • ✓Sits in the last housing
Measure your housing before you order
  • About 4.5″ wide and 10″ tall, with 1″ ports: this cartridge fits.
  • Narrow, about 2.5″ wide with 3/4″ ports: you need a 10″ × 2.5″ cartridge. Find your model →
  • About 4.5″ wide and 20″ tall: you need a 20″ × 4.5″ cartridge. Ask us →

Specifications

Model / SKU SCALE-10BB
Media Food-grade polyphosphate crystals (salt-free)
Rating 25 micron (nominal)
Size Standard 10″ × 4.5″ heavy-duty whole-house housings
Position Final stage — after sediment and carbon
Pressure Max 90 PSI · above 80 PSI, fit a pressure regulator
Temperature 40–100 °F (4–38 °C), cold water only
Typical life About 6 months
Brand My Water Club

Reorder this filter

Order the same cartridge

Order by SKU SCALE-10BB.

View on MyWaterClub.com →

Buy on Amazon →
Other option
IRON-10BB — Iron reduction + softening resin

Hard water with orange staining from dissolved iron? This resin reduces dissolved iron, manganese and some hardness.

Support page →  ·  View on MyWaterClub.com →

My Water Club systems that use this filter

It isn’t standard in any system. Add it as the last stage with an extra HOUSING10BB housing, after sediment and carbon. It also fits other standard 10″ × 4.5″ housings, including our HOUSING10BB.

Good to know

  • It is not a water softener. Your water will still test “hard” — polyphosphate helps keep the minerals suspended so less scale forms.
  • Install it on the cold line before the water heater, where scale builds up the most.
  • The crystals dissolve slowly as they work. Change the cartridge about every 6 months, even if nothing looks wrong.

When to change your filter

Part Typical interval Change sooner if…
This cartridge (SCALE-10BB) About 6 months Very hard water or high water use · scale or spotting builds up again
Housing O-ring Inspect at every change · replace every 12–24 months Cracked, flattened, brittle or weeping at the seam (O-ring sets)
Filter housing About every 3–4 years Crazing, hairline cracks, cloudiness, or a leak a new O-ring doesn’t stop (HOUSING10BB)

Intervals are estimates. Water chemistry, pressure and usage all change them.

Changing your filter

  1. Shut off the water: close the valves on both sides of the system (or the bypass), or the main shut-off.
  2. Open a cold tap downstream, then press the pressure release button on the cap until the hissing stops.
  3. Put a bucket and towels underneath — a 10″ × 4.5″ housing holds over a gallon of water.
  4. Unscrew the sump with the housing wrench (counterclockwise, looking up from below), supporting its weight.
  5. Remove the old cartridge and rinse the sump with clean water only — no soap or bleach.
  6. Inspect the O-ring and replace it if it’s damaged. Coat it lightly with food-grade silicone grease (never petroleum jelly).
  7. Unwrap the new cartridge and stand it centered on the post in the sump.
  8. Screw the sump on by hand, then snug it with the wrench — no more than a quarter turn. Don’t overtighten.
  9. Turn the water back on slowly. Press the release button to let air out, and check for leaks now and again after 12 hours.
  10. Run a cold tap for 2–3 minutes to flush the new cartridge.
  11. Write the change date on the housing, a magnet or the manual.

What to put before it

Polyphosphate goes in the last stage, after sediment and carbon, on the cold line before the water heater.

Cartridge Good for What it does
SED5-10BB Stage 1 on most water 5 µm melt-blown polypropylene · captures dirt, silt, sand & rust particles
SED5-PLT-10BB Heavy sediment, well water 5 µm pleated polyester · rinse and reuse
CTO-10BB Everyday city water Carbon block, 10 µm · reduces chlorine, taste & odor · lowest cost block
CACB-10BB Taste & odor Coconut carbon block, 10 µm · the usual pick for taste & odor · 6–12 month life
GAC-10BB City water · lowest cost carbon Granular carbon for chlorine, taste, odor & VOCs at full flow

Browse all 10″ × 4.5″ cartridges → · Free basic water testing in San Diego →

Common questions

  1. Will my water test soft?
    No. It still tests “hard”. Polyphosphate helps keep the minerals suspended, so less scale forms.
  2. Where should it go?
    Last, after sediment and carbon, on the cold line before the water heater.
  3. Can it go on the hot water line?
    No — cold water only, 40–100 °F.
  4. The crystals are almost gone.
    Time to change it. The crystals dissolve slowly as they work; most homes change it about every 6 months.
  5. There’s a leak where the housing meets the cap.
    The O-ring isn’t seated, or it’s worn. Shut off the water, press the release button, then reseat or replace the O-ring and coat it lightly with food-grade silicone grease.
  6. The housing won’t unscrew.
    Usually there’s still pressure inside, or it was overtightened. Make sure the water is off, press the release button, then use the housing wrench.

Need help?

Contact us
Send a photo of your cartridge or housing and we’ll identify it.

Get in touch →

All manuals
Instructions for every My Water Club system.

Browse manuals →

San Diego area service
In-person help and free basic water testing.

Local service →

Warranty & returns
What’s covered and how to start a return.

View policy →

Call or text (858) 345-7345. Bought on Amazon? You can also use Your Orders › Contact seller.

Scope and disclaimers

This cartridge treats the contaminants named on this page only. It doesn’t make unsafe water safe to drink. Treat untested well water, or water under a boil-water advisory, before relying on any filter.

Filter life and reduction performance depend on your water chemistry, pressure and usage, so results vary from home to home. Intervals on this page are typical estimates, not guarantees. Our filters are not certified to treat water of unknown quality and are not a substitute for testing your water. Descriptions use general, qualified language and are not health claims.