Description
5 Micron High-Quality Sediment Filter Cartridge – 10″ × 2.5″
This 5 micron sediment filter cartridge is designed to effectively reduce
dirt, silt, sand, rust, and scale particles from incoming water. It helps protect
downstream filters, RO membranes, plumbing fixtures, and appliances by capturing particulate
contaminants before they enter later filtration stages.
Manufactured to standard 10″ × 2.5″ dimensions, this cartridge is compatible with most
undersink reverse osmosis (RO) systems and whole house water filtration systems
that use standard-size housings.
Purpose
- Designed for use as the first stage (pre-filter) in:
- Undersink reverse osmosis (RO) systems
- Whole house water filtration systems
Key Features
- 5 micron nominal filtration for effective sediment reduction
- Removes dirt, silt, sand, rust, and scale particles
- Helps extend the life of carbon filters and RO membranes
- Standard size fits most 10″ filter housings
- Suitable for residential and light commercial applications
Specifications
- Filter Size: 10″ × 2.5″ (Standard Size)
- Micron Rating (Nominal): 5 Micron
- Operating Temperature: 36°F – 100°F
- Maximum Flow Rate: Up to 8 GPM
- Maximum Pressure: 100 PSI
- Service Life: 3–12 months (depending on water quality and usage)
- Brand: Aqua
Replacement Recommendation
Replace every 3 to 12 months, depending on sediment load, water quality, and system usage.
SKU: SED5, SED105, SED5-10
Used as the first stage in 3-stage systems
| Cartridge Comparison Chart – 10″ × 2.5″ (9 7/8″ × 2.5″) | ||||
|---|---|---|---|---|
| SKU | Cartridge Type | Purpose | What It Removes | Iron & H2S Effectiveness / Best Use |
| First Stage – Sediment Filtration | ||||
| SED5 (SED5-10) | Standard Sediment 5 Micron | Basic sediment removal to protect downstream filters | Sand, dirt, rust, silt | • Municipal water • Low–moderate sediment load |
| SED5-PLT | Pleated Sediment | High-capacity Multi Use filter with extended service life (more surface area) | Sand, dirt, silt, debris | • Well water / high sediment • Longer service intervals |
| Second Stage – Carbon Filtration | ||||
| GAC (GAC-10) | Media: GAC Carbon | Chlorine taste & odor reduction | Chlorine, Chloramine, taste, odor | • No iron / sulfur removal |
| CAT-10 | Media: Catalytic Carbon (Centaur Catalityc Calgon) | Advanced chemical reduction (better for chloramine vs. standard GAC) | Chlorine, chloramine, VOCs, solvents, H2S (rotten egg odor), low iron |
• Iron: effective for trace/low levels (about up to ~0.3 ppm) • H2S: mild odor reduction |
| CATKDF85-10 | Media: Catalytic Carbon + KDF-85 (3/4 lbs) | Iron & sulfur odor reduction plus broad chemical filtration | Iron, H2S, chlorine/chloramine, VOCs, heavy metals (redox treatment) |
• IRON: stronger reduction; suitable for light–moderate iron (about ~1–3 ppm) • H2S (rotten egg): stronger, more consistent odor reduction • Manganese: effective for LOW manganese only: approximately 0.1–1.0 ppm (mg/L) |
| Third Stage – Carbon Block / Polishing | ||||
| CTO-10 (CTO105) | Standard CTO Block | Final carbon filtration / polishing | Chlorine, taste, odor | • Standard use • Great as final polishing stage |
| CBCO-10-5 | Activated Coconut Carbon Block | Enhanced polishing with premium adsorption | Chlorine, VOCs, chemicals, taste & odor. Coconut-shell carbon provides higher adsorption efficiency, cleaner taste, and lower ash content compared to standard carbon blocks. | • Premium taste-focused use • Higher performance adsorption |
Important Performance Notes
🔩 Iron Removal Clarification
-
CAT-10 (Catalytic Carbon only)
-
Provides limited iron reduction
-
Best for trace iron typically found in municipal water
-
Effective range: up to ~0.3 ppm
-
Not intended as a primary iron filter
-
-
CATKDF85-10 (Catalytic Carbon + KDF-85)
-
Significantly stronger iron reduction due to redox reaction
-
Suitable for light to moderate iron levels
-
Effective range: up to ~1–3 ppm in cartridge (non-backwashing) systems
-
Helps prevent iron fouling of downstream filters
-
🥚 Hydrogen Sulfide (Rotten Egg Smell)
-
Catalytic carbon converts hydrogen sulfide through oxidation
-
CAT-10: effective for mild sulfur odor
-
CATKDF85-10: enhanced H₂S reduction, more stable performance, longer media life
-
For high sulfur levels, a backwashing system or aeration is recommended
⚙️ Manganese
-
CATKDF85-10. Effective for LOW manganese only: approximately 0.1–1.0 ppm (mg/L)
💊 Pharmaceuticals and pesticides reduction
-
-
CATKDF85-10: Catalytic carbon is an effective medium designed to help reduce pesticides, herbicides, PFAS, and pharmaceuticals, offering improved performance compared to standard GAC filters
-
Quick Selection Guide
-
-
Chloramine + mild sulfur odor: → CAT-10
-
Iron + sulfur odor (well water): → CATKDF85-10
-
Trace iron only (<0.3 ppm): → CAT-10
-
Iron above 1 ppm: → CATKDF85-10 (or dedicated iron filter for higher levels)
-
High sediment / well water: → SED5-PLT
-
Chloramine removal: → CAT-10
-
Iron + chemical reduction: → CATKDF85-10
-
Best taste & drinking water quality: → CBCO-10-5
- Premium setup→ SED5 + CATKDF85-10 + CBCO-10-5
-



Reviews
There are no reviews yet.