Description
A high-capacity 5 micron sediment filter in heavy-duty 10″ × 4.5″ (BB) size that captures dirt, silt, sand and rust particles at whole-house flow rates — the essential first stage that protects every filter after it.
What this 5 micron sediment filter does
This 5-micron melt-blown polypropylene sediment cartridge is the first stage of a whole-house filtration system. Installed on the main water line, it captures dirt, silt, sand and rust particles as water enters your home — before that grit can reach anything downstream.
The oversized heavy-duty 10″ × 4.5″ format holds far more media than a slim 10″ × 2.5″ cartridge, which means higher flow with less pressure drop and much greater dirt-holding capacity — exactly what a whole-house line demands. Its graded melt-blown structure traps larger particles in the outer layers and finer ones toward the core, so the cartridge loads evenly instead of blinding off at the surface.
Trapping particulate up front does two jobs: it keeps your water clear, and it protects everything downstream — carbon cartridges, specialty media, plumbing fixtures, water heaters, and appliances all last longer when they aren’t clogged by sediment. Replacing an inexpensive sediment filter on schedule is the cheapest way to extend the life of pricier stages.
Key benefits
- ✓ 5-micron nominal filtration for effective sediment reduction
- ✓ Reduces dirt, silt, sand & rust particles
- ✓ High-flow heavy-duty 10″ × 4.5″ design with low pressure drop
- ✓ Excellent dirt-holding capacity — fewer changes than slim cartridges
- ✓ Extends the life of carbon & specialty media stages
- ✓ Replaces same-size 5 micron cartridges from Culligan, iSpring, Hydronix, Watts & more*
Specifications
Helps reduce
What this cartridge targets — and what it isn’t built for.
Sand
Rust particles
Hardness / scale
Chlorine / taste
Iron / H₂S
Dissolved chemicals
Which 10″ × 4.5″ cartridge do I need?
The MyWaterClub heavy-duty 10″ × 4.5″ range by stage. Your current filter is highlighted — tap any other name to view it.
Browse all 10″ × 4.5″ BB cartridges & sets → · Specialty media →
Good to know before you buy
Always the first stage. Sediment goes before carbon and specialty media. Capturing grit up front is what protects those pricier stages — install this ahead of any other 10″ × 4.5″ cartridge.
Heavy-duty 10″ × 4.5″ vs. slim 10″ × 2.5″. Same job, much bigger body: more media surface means higher flow, less pressure drop, and longer intervals between changes. If your housing takes standard 10″ × 4.5″ (BB) cartridges — often called Big Blue® size — this is your size†. A slim cartridge will not seal in it.
When to change it. Replace every 3–6 months. Shorter if your water carries more sediment or you notice a pressure drop — a clogged sediment filter chokes flow to the whole house.
Compatible housings & replacement cartridges
SED5-10BB is a standard 10″ × 4.5″ melt-blown cartridge (9¾″ × 4.5″ actual), rated 5 micron. It fits the housings below and can replace the same-size 5 micron sediment cartridges listed after them.*
Housings & systems it fits
Replacement for Culligan CW5-BBS, iSpring FP15B, Hydronix SDC-45-1005 & more
Also searched as: DGD5005 · 15535743 · CW5BBS · SDC451005 · PWMB10FFM5 · WDGD5005
Check before you order. Your old cartridge should be about 4.5″ across and 9¾–10″ long, with an open center hole at both ends. Not sure? Send us a photo of the cartridge label and we’ll confirm the fit.
Replacing a coarser cartridge? If yours is 20–50 micron (for example Culligan P25-BBSA or R50-BBSA, or Whirlpool WHKF-GD25BB), SED5-10BB fits the same housing but catches finer particles, so on heavy sediment it may need changing sooner. For heavy sediment, the washable pleated SED5-PLT-10BB is the better match.
Fit questions
Does SED5-10BB replace the Pentek DGD-5005?
It fits the same Big Blue® #10 housings† and has the same 5 micron rating and 10″ × 4.5″ size. The DGD-5005 is a dual-gradient spun cartridge; SED5-10BB is a graded melt-blown cartridge.
Does SED5-10BB fit the Culligan HD-950A housing?
Yes. The HD-950A, HD-950 and WH-HD200-C take standard 10″ × 4.5″ cartridges, so SED5-10BB drops in where the Culligan CW5-BBS goes. Both are rated 5 micron.
Can I use it instead of Hydronix SDC-45-1005 or Watts PWMB10FFM5?
Yes, for most homes. All three are 5 micron, 4.5″-diameter polypropylene sediment cartridges about 9¾–9⅞″ long, so they fit the same housings.
Will it work as Stage 1 in an iSpring WGB21B?
Yes, in the first (sediment) housing in place of the iSpring FP15B. Keep a carbon cartridge in Stage 2.
Does it replace a pleated cartridge like the Watts WPC5FF975?
It fits the same housing. The difference is that pleated cartridges can be rinsed and reused, while SED5-10BB is a melt-blown depth cartridge you replace. If you want washable, see SED5-PLT-10BB.
Building a full stack?
† Big Blue® and Pentek® are registered trademarks of Pentair. My Water Club is not affiliated with, sponsored by or endorsed by Pentair. These names are used only to describe size and compatibility.
* 3M and Aqua-Pure, American Plumber, Aqua Flo (WaterGroup), AXEON, Culligan, Express Water, Filters Fast, GE, Hydronix, iSpring, KleenWater, Tier1, USWF, VIQUA, Waterdrop, Watts and Whirlpool, and their model names, are trademarks of their respective owners. My Water Club is not affiliated with, sponsored by or endorsed by these companies, and this cartridge is not made by them. Brand and model names are used only to identify housings this cartridge fits and the same-size cartridges it can replace. Compatibility is based on the standard 10″ × 4.5″ size; please check your housing before ordering.









Reviews
There are no reviews yet.