My Water Club Product Support

Washable Pleated Sediment Filter — 10″ × 4.5″

SED5-PLT-10BB

Specifications, how to change it, which housings it fits, and what to pair it with.

My Water Club SED5-PLT-10BB washable pleated sediment cartridge
Is this your filter?

Check the cartridge in your housing against this list.

  • ✓A large cartridge, about 4.5″ wide and 10″ long
  • ✓Deep folded pleats of fabric around the outside
  • ✓Label reads SED5-PLT-10BB · 5 micron
  • ✓Sits in the first housing that water enters
Measure your housing before you order
  • About 4.5″ wide and 10″ tall, with 1″ ports: this cartridge fits.
  • Narrow, about 2.5″ wide with 3/4″ ports: you need a 10″ × 2.5″ cartridge. Find your model →
  • About 4.5″ wide and 20″ tall: you need a 20″ × 4.5″ cartridge. Ask us →

Specifications

Model / SKU SED5-PLT-10BB
Media Pleated polyester sediment cartridge — washable
Rating 5 micron (nominal)
Size Standard 10″ × 4.5″ heavy-duty whole-house housings
Position Stage 1 — always first in line
Pressure Max 90 PSI · above 80 PSI, fit a pressure regulator
Temperature 40–100 °F (4–38 °C), cold water only
Typical life Rinse when flow drops · replace when damaged
Brand My Water Club

Reorder this filter

Order the same cartridge

Order by SKU SED5-PLT-10BB.

View on MyWaterClub.com →

Buy on Amazon →
Other option
SED5-10BB — Disposable 5 micron sediment

The lower-cost choice for lighter, finer sediment, such as most city water. You replace it instead of rinsing.

Support page →  ·  View on MyWaterClub.com →

My Water Club systems that use this filter

System Where it goes More
Single-stage system (WHS-1S-10BB) in place of SED5-10BB System support page →
Dual-stage system (WHS-2SC-10BB-E) first housing, in place of SED5-10BB System support page →
Triple-stage system (WHS-3SGC-10BB-E) first housing, in place of SED5-10BB System support page →
Triple-stage system with coconut carbon block (WHS-3SGCACB-10BB-A) first housing, in place of SED5-10BB View system →

It also fits other standard 10″ × 4.5″ housings, including our HOUSING10BB.

Good to know

  • How to rinse: after removing it (steps 1–4 below), hose the pleats from the outside in until the runoff is clear. A soft brush helps on stubborn buildup. Then reinstall it from step 5.
  • Lighter, finer sediment (most city water)? The disposable SED5-10BB is the lower-cost choice.
  • It doesn’t reduce chlorine or taste. Keep a carbon stage behind it for that.

When to change your filter

Part Typical interval Change sooner if…
Pleated cartridge (SED5-PLT-10BB) Rinse when pressure drops · replace when it no longer rinses clean Fabric torn or deformed · flow stays low even after a thorough rinse
Housing O-ring Inspect at every change · replace every 12–24 months Cracked, flattened, brittle or weeping at the seam (O-ring sets)
Filter housing About every 3–4 years Crazing, hairline cracks, cloudiness, or a leak a new O-ring doesn’t stop (HOUSING10BB)

Intervals are estimates. Water chemistry, pressure and usage all change them.

Changing your filter

  1. Shut off the water: close the valves on both sides of the system (or the bypass), or the main shut-off.
  2. Open a cold tap downstream, then press the pressure release button on the cap until the hissing stops.
  3. Put a bucket and towels underneath — a 10″ × 4.5″ housing holds over a gallon of water.
  4. Unscrew the sump with the housing wrench (counterclockwise, looking up from below), supporting its weight.
  5. Take out the cartridge. To reuse it, hose the pleats from the outside in until the runoff is clear; replace it if the fabric is torn. Rinse the sump with clean water only.
  6. Inspect the O-ring and replace it if it’s damaged. Coat it lightly with food-grade silicone grease (never petroleum jelly).
  7. Unwrap the new cartridge and stand it centered on the post in the sump.
  8. Screw the sump on by hand, then snug it with the wrench — no more than a quarter turn. Don’t overtighten.
  9. Turn the water back on slowly. Press the release button to let air out, and check for leaks now and again after 12 hours.
  10. Run a cold tap for 2–3 minutes to flush the new cartridge.
  11. Write the change date on the housing, a magnet or the manual.

What to put after it

A sediment filter only traps particles. It doesn’t reduce chlorine, taste, odor, dissolved iron or hardness. In a 2- or 3-stage system, these cartridges go after it, so the sediment stage keeps grit off them.

Cartridge Good for What it does
CTO-10BB Everyday city water Carbon block, 10 µm · reduces chlorine, taste & odor · lowest cost block
CACB-10BB Taste & odor Coconut carbon block, 10 µm · the usual pick for taste & odor · 6–12 month life
GAC-10BB City water · lowest cost carbon Granular carbon for chlorine, taste, odor & VOCs at full flow
CAT-10BB Chloraminated city water Centaur® catalytic carbon · helps reduce chloramine, chlorine & low-level H₂S odor
CATKDF85-10BB Chloramine, H₂S odor, some metals Catalytic carbon + KDF-85 copper-zinc media
BC-10BB Fluoride Bone char · helps reduce fluoride and some heavy metals; results depend on contact time and water chemistry
IRON-10BB Clear-water iron on wells Reduces dissolved iron, manganese & some hardness · not for water that comes out orange
SCALE-10BB Limescale Polyphosphate helps prevent scale in pipes & appliances · not a softener

Browse all 10″ × 4.5″ cartridges → · Free basic water testing in San Diego →

Common questions

  1. When do I rinse it, and when do I replace it?
    Rinse it whenever whole-house pressure drops. Replace it when the fabric is torn or deformed, or when flow stays low even after a thorough rinse.
  2. Pressure is still low after rinsing.
    Rinse again from the outside in, using a soft brush on stubborn buildup. If it still won’t come clean, the pleats are loaded for good — replace it.
  3. There’s a leak where the housing meets the cap.
    The O-ring isn’t seated, or it’s worn. Shut off the water, press the release button, then reseat or replace the O-ring and coat it lightly with food-grade silicone grease.
  4. Water seems to pass through unfiltered.
    The cartridge isn’t centered on the post, or it’s the wrong size. A slim 2.5″ cartridge won’t seal in a 10″ × 4.5″ housing.
  5. The housing won’t unscrew.
    Usually there’s still pressure inside, or it was overtightened. Make sure the water is off, press the release button, then use the housing wrench.
  6. The water still tastes or smells of chlorine.
    That’s expected — sediment media doesn’t treat chlorine. A carbon cartridge in the next housing does that job (see “What to put after it”).
  7. The water is cloudy right after a change.
    That’s air. It clears after a few minutes of running water.

Need help?

Contact us
Send a photo of your cartridge or housing and we’ll identify it.

Get in touch →

All manuals
Instructions for every My Water Club system.

Browse manuals →

San Diego area service
In-person help and free basic water testing.

Local service →

Warranty & returns
What’s covered and how to start a return.

View policy →

Call or text (858) 345-7345. Bought on Amazon? You can also use Your Orders › Contact seller.

Scope and disclaimers

This sediment filter reduces particles only. It doesn’t make unsafe water safe to drink. Treat untested well water, or water under a boil-water advisory, before relying on any filter.

Filter life and reduction performance depend on your water chemistry, pressure and usage, so results vary from home to home. Intervals on this page are typical estimates, not guarantees. Our filters are not certified to treat water of unknown quality and are not a substitute for testing your water. Descriptions use general, qualified language and are not health claims.