Free U.S. Continental Shipping on orders $35+ ● No Sales Tax outside California
MyWaterClub Product Support
Re-Mineralization Multi-Media Inline Filter — 10″ × 2″, 3/8″ Quick Connect
MIN-MCB-QC38
Label reorder # MIN-MMCB-QC38
This page covers where the filter goes, how to install it, when to change it, how to test TDS and pH, and the parts that fit it.
Is this your filter?
Check these against the filter in your hand. All four should match.
- ✓A white inline filter about 10″ long and 2″ across
- ✓The label says Multi-Media Inline Re-Mineralization Filter
- ✓3/8″ quick-connect ports at both ends and a flow arrow on the label
- ✓SKU / REORDER # MIN-MMCB-QC38 in the green box on the label
Remineralization, alkaline or carbon? Check the label
- Re-Mineralization, 3/8″ ports — this page. A gentle filter: pH about 7.5–8.3.
- Alkaline, 3/8″ ports — a stronger filter that raises pH higher, about 8.2–9.5. ALC-FMB-QC38 support page →
- Alkaline, 1/4″ ports (for countertop RO and 1/4″ tubing) — ALK-QC support page →
- Carbon, sediment, DI or specialty — see the full guide for all inline filters. Inline filter guide →
Specifications
| Model / SKU | MIN-MCB-QC38 (website and Amazon) · label reorder # MIN-MMCB-QC38 |
| Media | 4-media blend: far-infrared mineral stone, coral red stone, maifan stone and bio-ceramic media |
| What it does | Adds minerals back to RO water and gently raises its pH to about 7.5–8.3, near neutral and not strongly alkaline, for a smoother taste (varies with source water, flow and contact time) |
| Size | 10″ × 2″ |
| Connection | 3/8″ quick connect, for 3/8″ OD tubing |
| Pressure / temperature | Max 90 PSI · 36–100°F, cold water only |
| Typical life | 6–12 months, or 400 gallons |
| Made in | Taiwan |
| Brand | MyWaterClub |
Reorder this filter
This filter · MIN-MCB-QC38
Remineralization Inline Filter, 3/8″ Quick Connect
Buy one at a time or stock up. The price per filter drops when you buy more.
Where it goes
A remineralization filter is always the last stage, and it is for RO water only. It adds minerals back after the RO membrane has removed them. Its 3/8″ ports suit under-sink RO systems with 3/8″ tubing; countertop RO systems use 1/4″ tubing and need a filter with 1/4″ ports, or 1/4″-to-3/8″ adapters. All remineralizing inline filters →
| Your setup | Order of stages |
|---|---|
| Under-sink RO | Pre-filters → RO membrane → storage tank → carbon post filter → remineralization filter → faucet |
| Fridge or ice maker line | Only when the line is fed by RO water: RO system → remineralization filter → appliance |
Where not to use it
- On a plain tap water line — tap water already has minerals.
- On an air humidifier — added minerals leave white dust.
- Before the RO membrane — the membrane would remove what the filter adds.
- Before any carbon filter, including the carbon post filter — carbon takes out part of the minerals this filter adds. Put the remineralization filter after it.
Connections
Before you cut anything
- Check your tubing size. It is either 1/4″ OD or 3/8″ OD, usually printed on the tubing. Use the matching adapters. Never force 1/4″ tubing into a 3/8″ port, or the reverse.
- Water must flow the way the arrow on the label points.
- You need a tubing cutter (or a sharp utility knife), a towel and a small bucket.
- 3/8″ tubing goes straight into the filter’s quick-connect ports. Have 1/4″ tubing? Use 1/4″-to-3/8″ adapters, or a remineralizing filter with 1/4″ ports.
- Cut the tubing square. A 90° cut. A cut off by about 15° or more will leak. The last inch should be round, smooth and free of scratches.
- Remove any blue C-clips from the adapters. A clip left in stops the tube from seating.
- Push the tube in until it stops, then pull gently to confirm it holds.
- Refit the blue C-clips on every quick-connect port.
To remove a tube later: turn off the water and release pressure, take off the C-clip, push the collar in toward the filter and pull the tube out while holding the collar.
Installing on an under-sink RO
First time? Watching a short video helps: search YouTube for “add inline filter to RO system”.
- Shut off the RO water supply and the tank valve, then open the RO faucet to release pressure.
- Find the spot: after the storage tank and the carbon post filter, right before the faucet.
- Check that the tubing is 3/8″ OD, then cut it square over a towel.
- Connect the filter with the arrow on the label pointing toward the faucet, and refit the C-clips.
- Secure the filter with a clip: a 2.5″ × 2″ clip onto the membrane housing, or a 2″ × 2″ clip onto another inline filter.
- Open the supply and tank valves. Check for leaks now, after 10 minutes, and the next day.
- Flush the new filter for at least 5 minutes with the RO faucet open. Let the tank fill, then discard the first full tank.
- Write the install date on the label.
Countertop RO: these systems use 1/4″ tubing, so use a remineralizing filter with 1/4″ ports. It goes last, after the carbon post filter.
When to change your filter
| Filter | Typical interval | Change sooner if… |
|---|---|---|
| Remineralization filter | 6–12 months or 400 gallons |
TDS no longer rises across the filter, or the taste goes flat again |
Intervals are typical estimates. Your source water, flow and usage set the real schedule.
Testing pH and TDS
- Wait one week after installing a new filter. The first water through a new mineral filter reads higher than normal.
- TDS goes up after this filter. That is expected — it adds minerals. Measure TDS right after the RO membrane to judge the membrane.
- pH: plain RO water is usually slightly acidic, about 6–7. This filter gently raises it, to about 7.5–8.3. Run the water for a minute and test right away, because RO water’s pH drops within minutes in an open cup.
- Use a calibrated pH meter. Calibrate it with pH 7 and pH 4 or pH 10 buffer solutions before you test. pH strips and test drops are not accurate enough in low-mineral RO water, so we don’t recommend them.
Full testing steps in the inline filter guide → · Digital pH meter →
Parts that fit this filter
| Part | Notes |
|---|---|
| Coconut carbon block post filter, 3/8″ QC (CB5-QC38) | Goes right before the remineralization filter · all inline carbon filters |
| Blue C-clips for 3/8″, 10-pack | Locks the tube in a 3/8″ port · clips for 1/4″ ports |
| 2.5″ × 2″ mounting clips, 2-pack | Clips the filter onto an RO membrane housing · 2″ × 2″ clips · 2″ screw-mount clips |
| Tubing cutter with release tool | Square cuts on 1/4″ and 3/8″ tubing |
| 3/8″ OD tubing, white | If you need extra length · 1/4″ tubing |
All tubing, clips and fittings →
Common questions
| What you’re seeing | Most likely cause |
|---|---|
| Cloudy or milky water from a new filter | Fine mineral particles or trapped air. Flush for at least 5 minutes; bubbles clear within a day or two. |
| Drip at a quick-connect port | Tube not fully in, scratched or cut at an angle, or the C-clip was left in. Release, recut square, push it fully in and refit the clip. |
| Low flow at the faucet | Filter installed backward (check the arrow on the label), kinked tubing, or a filter past its date. Check the tubing and the install date. |
| TDS is higher after this filter | Expected — the filter adds minerals. Judge the RO membrane by testing before this filter. |
| pH readings jump around | Normal in low-mineral water. Calibrate the meter, stir gently and wait for the reading to settle. |
| pH and TDS are back near plain RO water | The mineral media is used up. Time for a new filter. |
Need help?
Contact us
Send a photo of the filter label and your system, and we’ll tell you where it goes
Call or text (858) 345-7345. Bought on Amazon? You can also reach us through Amazon: Your Orders › Contact seller.
Scope note: This is a taste and mineral step for RO water, not a contaminant filter. It does not reduce chlorine, sediment or fluoride. Use it on municipally treated or otherwise microbiologically safe water. Descriptions refer to taste and mineral content only and are not health claims.
Please note: pH, mineral levels and filter life depend on your source water, flow rate, contact time and usage, so results vary from home to home. This product is not a substitute for testing your water.